8 pot breakout PCB 35mm pitch

8-Pot Sequencer Panel PCB (35x Pitch)

 
£4.18
(£3.48 exc. tax)
7210-709
20.00 g.
In stock
+
Add to wish list

Introduction

We find that wiring a MFOS PCB to the front panel controls is both time consuming and often detracts from the overall finish. We are not able to alter the MFOS PCBs to make panel wiring easier so we approached the problem from a different angle. We chose to mount the front panel controls on a mini PCBs (breakout boards) that take the panel controls to a JST type XH socket into which is plugged a lead. This lead is then dressed to the main MFOS PCB (or sometimes to other panel controls) and soldered into the respective pads. Many breakout boards have solderable jumpers for making common connections as well as thin tracks to cut where panel mounted resistors need to be connected inline with say a pot wiper. MFOS projects may require multiple breakout boards so we bundle these altogether and offer them in one ST Synth Panel Breakout PCB Set. The pack description will further describe the wiring colour code and what if any links need to be made or cut.

This method does have other advantages other than just time saving and appearance:

  • Time saving
  • Neater more professional appearance - improves resale value
  • Takes care of common connections between panel components
  • Has space to accommodate panel mounted resistors and capacitors
  • Can improve reliability - have you tried soldering a diode, LED and a wire to one pin on a toggle switch on the 16-step sequencer?
  • Makes fault finding easier

If you have any reservations about using connectors, then simply solder wires direct to the breakout boards. Takes longer but you still get all of the other advantages.

The boards are designed to fit our front panel component spacing so you will see references to pitch and whether it is in the 'x' or 'y' or both direction. At the time of writing, there was 30+ breakout boards developed for pots (using pot brackets), sockets (jack and banana), switches and LEDs. Whilst these will not take care of every panel component on over 40 MFOS projects, it will go a long way to achieving it. As we work through making up each MFOS project with these breakout boards, we will see where improvements can be made or even create more breakout boards to provide the best possible solution.

Specific Information on the 8-Pot Sequencer Panel PCB (35x Pitch). Board size: 274x22mm

7210-709 accommodates 8 of our commercial grade synth pots along with our pot mounting brackets on a 35mm horizontal pitch. Each of the pot slider terminals are wired through to a 10-way connector / lead (see 7210-110). Specific wiring information can be found in the ST Synth Panel Breakout PCB Set for the MFOS Sequencer projects.

Two CW & CCW connection pads are provided to continue these commons through to other 8-pot panel PCBs if required.

Assembly

  1. Solder in the socket noting that the slots in the socket housing point towards the top of the board
  2. Remove any anti-rotation lugs on the pots
  3. Insert pot into bracket and temporarily do up lock nut
  4. Insert pot with bracket into PCB and solder in position ensuring the pot bracket sits flat on PCB.
  5. Repeat for remaining pots
  6. Remove pot nuts
  7. Install assembled board into panel front and tighten pot nuts (washers not required)
  8. Plug in cable assembly and wire to main MFOS PCB as required

Wiring Colour Code

Colour Function
Black Pot 1 Slider
Red Pot 2 Slider
White Pot 3 Slider
Yellow Pot 4 Slider
Orange Pots 1-8 CCW Common
Green Pots 1-8 CW Common
Blue Pot 5 Slider
Violet Pot 6 Slider
Grey Pot 7 Slider
Brown Pot 8 Slider

It is always worth checking the wire colour sequence to ensure it matches the above just in case there has been a mistake at the factory in the assembly of the cable.

Typical examples of projects that use this board: 16-Step Analogue Sequencer (not the quantized version, see 7210-708)

No FAQ found

No posts found

Write a review