8x2y Sequencer Toggle Switch + LED Panel PCB (35x)

8x2y Sequencer Toggle Switch + LED Panel PCB (35x)

 
£6.26
(£5.22 exc. tax)
7210-799
20.00 g.
In stock
+
Add to wish list

Introduction

We find that wiring a MFOS PCB to the front panel controls is both time consuming and often detracts from the overall finish. We are not able to alter the MFOS PCBs to make panel wiring easier so we approached the problem from a different angle. We chose to mount the front panel controls on a mini PCBs (breakout boards) that take the panel controls to a JST type XH socket into which is plugged a lead. This lead is then dressed to the main MFOS PCB (or sometimes to other panel controls) and soldered into the respective pads. Many breakout boards have solderable jumpers for making common connections as well as thin tracks to cut where panel mounted resistors need to be connected inline with say a pot wiper. MFOS projects may require multiple breakout boards so we bundle these altogether and offer them in one ST Synth Panel Breakout PCB Set. The pack description will further describe the wiring colour code and what if any links need to be made or cut.

This method does have other advantages other than just time saving and appearance:

  • Time saving
  • Neater more professional appearance - improves resale value
  • Takes care of common connections between panel components
  • Has space to accommodate panel mounted resistors and capacitors
  • Can improve reliability - have you tried soldering a diode, LED and a wire to one pin on a toggle switch on the 16-step sequencer?
  • Makes fault finding easier

If you have any reservations about using connectors, then simply solder wires direct to the breakout boards. Takes longer but you still get all of the other advantages.

The boards are designed to fit our front panel component spacing so you will see references to pitch and whether it is in the 'x' or 'y' or both direction. At the time of writing, there was 30+ breakout boards developed for pots (using pot brackets), sockets (jack and banana), switches and LEDs. Whilst these will not take care of every panel component on over 40 MFOS projects, it will go a long way to achieving it. As we work through making up each MFOS project with these breakout boards, we will see where improvements can be made or even create more breakout boards to provide the best possible solution.

Specific Information on the Toggle Switch / LED PCB (35x). Board size: 260 x 40mm

7210-799 PCB accommodates sixteen SPDT toggle switches, sixteen LEDs and 16 diodes. The required switch and LED connections are brought out to a 10-way and 8 way JST connectors (see 7210-110 & 7210-108).

Assembly

Solder in the 16 diodes marked D1 to D16 on the PCB)

Solder in the JST sockets noting that the slots in the socket housing point towards D4 & D5.

With the 16 toggle switches fixed in position on the panel, solder the PCB to the switch connections

The LEDs are soldered in only when you are ready for final assembly on the front panel.

We find it easiest to insert each LED one at a time, forming the LED legs to align with the PCB holes. Note that their orientation needs to match the PCB, the LED long lead goes to the pad with the A symbol.

Wiring Colour Code

U1 Pin 1 (black wire) is on the left of the board

Colour Function
Black S8
Red S7
White S6
Yellow S5
Orange GB
Green LED K Com
Blue S4
Violet S3
Grey S2
Brown S1

U2 Pin 1 (black wire) is on the left of the board

Colour Function
Black S16
Red S15
White S14
Yellow S13
Orange S12
Green S11
Blue S10
Violet S9

 

It is always worth checking the wire colour sequence to ensure it matches the above just in case there has been a mistake at the factory in the assembly of the cable.

 

Typical examples of projects that use this board: 16-Step sequencer (see 7210-798 for the quantized sequencer)

No FAQ found

No posts found

Write a review