Soundtronics Breakout Boards for Synths

MFOS Noise Cornucopia 5U Synth Panel Breakout PCB Set

 
£4.92
(£4.10 exc. tax)
7210-445
200.00 g.
In stock
+
Add to wish list

We find that wiring a MFOS PCB to the front panel controls is both time consuming and often detracts from the overall finish. We are not able to alter the MFOS PCBs to make panel wiring easier so we approached the problem from a different angle. We chose to mount the front panel controls on a mini PCBs (breakout boards) that take the panel controls to a JST type XH socket into which is plugged a lead (not included with set but available separately). This lead is then dressed to the main MFOS PCB (or sometimes to other panel controls) and soldered into the respective pads. Many breakout boards have solderable jumpers for making common connections as well as thin tracks to cut where panel mounted resistors need to be connected inline with say a pot wiper. MFOS projects may require multiple breakout boards so we bundle these altogether and offer them in one ST Synth Panel Breakout PCB Set. The pack description will further describe the wiring colour code and what if any links need to be made or cut.

This method does have other advantages other than just time saving and appearance:

  • Time saving
  • Neater more professional appearance - improves resale value
  • Takes care of common connections between panel components
  • Has space to accommodate panel mounted resistors and capacitors
  • Can improve reliability - have you tried soldering a diode, LED and a wire to one pin on a toggle switch on the 16-step sequencer?
  • Makes fault finding easier

If you have any reservations about using connectors, then simply solder wires direct to the breakout boards. Takes longer but you still get all of the other advantages.

The boards are designed to fit our front panel component spacing so you will see references to pitch and whether it is in the 'x' or 'y' or both direction. At the time of writing, there was 30+ breakout boards developed for pots (using pot brackets), sockets (jack and banana), switches and LEDs. Whilst these will not take care of every panel component on over 40 MFOS projects, it will go a long way to achieving it. As we work through making up each MFOS project with these breakout boards, we will see where improvements can be made or even create more breakout boards to provide the best possible solution.

The panel PCBs can also be used with our YuSynth range. YuSynth PCBs are better laid out as regards panel wiring but can still take advantage of these breakout PCBs.

This pack contains the following breakout PCBs:

  • 7210-704 x 1
  • 7210-723 x 1

Whilst you can solder wires between the breakout PCBs and the main PCB, we do recommend using our JST cable assemblies. For the VCO, you will need the following:

  • 7210-107 x 1
  • 7210-112 x 1

See the Build Guide tab for wiring information on how to use these breakout PCBs with this module.

Guidelines when building a Noise Cornucopia module using our panel PCBs, front and back panels, PCB holder and the MFOS main PCB.

Parts needed

  • Assembled MFOS PCB #7210-045
  • Front Panel #7210-545
  • Back Panel #7210-845
  • PCB Holder #7210-945
  • 4-Way Pot PCB #7210-704 (1 reqd.)
  • 6-Way 1/4" Jack Socket PCB #7210-723 (1 reqd.)
  • 12-way Cable Assemble #7210-112 (1 reqd.)
  • 7-Way Cable Assembly #7210-107 (1 reqd.)
  • PCB Holder Brackets Fixing Kit #7210-181
  • PCB Mounting Fixing Kit #7210-182
  • Additionally you will need our Switchcraft Jack Sockets #7212-206 (Pack of 6) + knobs of your choice, we use the Cliff KM20B

Panel PCB Preparation

PCB #7210-704,

The first task is to solder the bridges and wire links as follows:

  • Solder wire links between R5 & R6, R10 & R11 (note links can be seen in the photo below.

  1. Solder in JST headers noting that the slots in the socket housing point towards the top of the board on the pot
  2. Remove any anti-rotation lugs on the pots.
  3. Insert pot into bracket and temporarily do up lock nut
  4. Insert pot with bracket into PCB and solder in position using the photo above as a guide. Ensure it sits flat on PCB. Only solder the bracket lugs on the bottom of the board.
  5. Repeat for remaining pot
  6. Remove pot nuts

PCB #7210-723, is used for the 6 jack sockets.

Solder in the JST housing first.

Solder in the 6 jack sockets.

We prefer to place the sockets in the aluminium back panel and then place the PCB over the connections before soldering.

Next, assemble the front & rear panels along with the mounting brackets / PCB holder and each of the assembled panel breakout PCBs.

Mount the PCB to the PCB holder and then to the PCB brackets

Plug in the JST cable assemblies ensuring that the colour sequence is exactly as below. If it differs, check that you have soldered in the JST housings correctly and that the PCBs are the right way around.

Now comes the final task of soldering each of the wires to the respective points as follows (note Cut means cut the wire close to the JST connector):

Pot PCB

1 Black Cut
2 Red To Gnd on the Socket PCB*
3 White LEDA
4 Yellow GTF1
5 Orange GTF2
6 Green Cut
7 Blue Cut
8 Violet Cut
9 Grey Cut
10 Brown GRNS2
11 Black Cut
12 Red GRNS1

The LED is wired in to the bottom pads of positions R2 & R3 on the pot PCB, the cathode goes to R2.

The red wire is soldered to the Gnd pin of J5 on the socket board.

Socket PCB

1 Black RNGT
2 Red HPNS
3 White GHP
4 Yellow LPNS
5 Orange GNS
6 Green WNS
7 Blue Gnd

Note the yellow wire is soldered to the top of R9 position on the pot PCB and the orange wire to the top of R12 position. You can just about make out these connections on the photo below.

Dress the wiring, we use 100mm cable ties

Wiring is now complete except for the +/-12V supply whcih depends on your own system. We solder in a 3-core cable with a plug on the end which we use for power distribution in our racks. Next is a visual inspection and we also apply power before inserting chips to check for correct polarity across one of the IC sockets.

No FAQ found

No posts found

Write a review

Customers also bought ....

1205-360
£4.13 (£3.44 exc. tax)
1205-360
Pack of 6 coloured guitar/audio patch leads each 50cm long for connecting effects processors, sound modules, pedals etc. Also available in black coloured... read more
In stock
Price in points: 688 points

7201-078
£3.74 (£3.12 exc. tax)
7201-078
Pack of 6 guitar/audio patch leads for connecting effects processors, sound modules, pedals etc. Available in either black or coloured insulation.... read more
In stock

7210-001
£23.56 (£19.63 exc. tax)
7210-001
A bare PCB for the MFOS Voltage Controlled Oscillator which allows use of SOIC or DIP8 SSM2210 or SSM2212 dual NPN package or discrete matched NPN pair.... read more
In stock