YuSynth ADSR Module Bare PCB

£12.27
(£14.72 UK, incl VAT)
7220-020
In stock
+

YuSynth ADSR

Introduction

A bare double sided PCB 48x104mm (no need for the wire jumper links shown on the PCB layout) for the Yusynth ADSR synth module. These PCBs are manufactured by Soundtronics with a percentage of the sale going to the creator of the YuSynth - Yves Usson. These are early days for the YuSynth Modular Synth at Soundtronics, our plan is to stock PCBs for all of the projects as well as components, kits and front panels. This is going to take time but will eventually be as comprehensive as our MFOS range.

No components are included with the PCB but check out our Synth Components section where you should find what you need. We do suggest visiting the YuSynth ADSR project page for detailed information including Yves panel layouts but a summary is shown below.

Description

This new version of the ADSR module provides a control voltage that makes possible shaping the envelope of a continuous sound. It is mainly used to control the gain of a VCA module or drive the cut off frequency of a VCF module. As usual it is not restricted to these two obvious applications and can be extended to the control of many others modules.

This module has a GATE input. The GATE signal determines the start and duration of the envelope signal. Four parameters can be set using potentiometers :
  • Attack duration : 1ms to 1s (short option) 5ms to 10s (long option)
  • Decay duration :  1ms to 1s (short option) 5ms to 10s (long option)
  • Sustain level : 0 to 10V
  • Release duration :  1ms to 1s (short option) 5ms to 10s (long option)

The direct ADSR signal is available on one output within 0 to 10V range and the inverted ADSR signal is available on a second output either within 0 to -10V range or 10V to 0V range.

A push button is available to manually generate a direct GATE signal. The intensity of the output signal can be visualised by means of a simple LED.

The power draw of this module is rather low : 10mA +15V rail, 3.6 mA -15V rail.

The heart of this circuit is based on an original idea by Jonathan Jacky (1980, see references at the end of this page).

The PCB provides jumpers to select the short ADSR versus long ADSR option (a DPDT switch can be added to toggle between).

The PCB can accept a choice of three types of power connector, it can be either a Synthesizers.com 6 pins MTA connector, a MOTM 4 pins MTA96 connector or a 10-pin Eurorack connector.
The module was designed to work with a +15V/0V/-15V PSU but can be used without modifications with a +12V/0V/-12V PSU, however the output levels will be lower (around 8V instead of 10V)

Circuit

Click on the schematic thumbnail above for the circuit diagram.

The schematic of this module is rather simple and uses very common components. The 555 core of the schematic is based on an original idea by Jonathan Jacky that was published in Electronics ("Two-chip generator shapes synthesizer's sounds" Electronics #11, September 1980 : 137-138). This core has inspired other DIYers (Tom G.-EFM, René Schmitz).

Q1 and Q2 operate as a Schmitt trigger and turn any input signal as a suitable GATE signal. D1 protects the circuit from negative voltages. The trigger threshold is 2V. Diodes D2 to D4 are used to dispatch the charge and discharge current of the timing capacity C7/C8 (10µF/35V tantalum) through the potentiometers P1,P2 & P4. The 7555 chip (U1) is wired as a monostable timer. One OPA (TL074) is used to buffer the SUSTAIN voltage and avoids interference with the DECAY settings (otherwise the DECAY time would be affected by the SUSTAIN level). Two OPAs are used as a simple voltage follower and a voltage inverter, respectively. The fourth OPA drives the control LED. Note that J1 (BS170) has been introduced to break the DECAY circuit when the GATE signal returns to 0V before the DECAY cycle is finished. This insures that the capacitor will discharge through the RELEASE potentiometer rather through the DECAY circuit. Preferred behaviour of keyboardists...?

Wiring

The wiring schematic image in the above thumbnails show the panel wiring to the pots and sockets etc.

Setting and Trimming

No setting up or trimming required

Parts List

The parts list below is direct from the YuSynth website.

The parts list excludes knobs although we have standardised on the Cliff KM20B but it does include 1/4" jack sockets. All parts are available individually (use the part number in the search box above) or as a components kit that excludes sockets and knobs.

Reference Value Part No. Qty
U1 7555 (or any other CMOS version of the NE555, DO NOT USE A NE555 !) 7212-500 1
U2 TL074 7212-544 1
J1 BS170 7212-405 1
Q1, Q2, Q3 BC547C or equivalent (mind the pinout !) 7212-401 3
D1,D2,D3,D4, D5 1N4148 7212-480 4
R1,R2, R9 10 ohms 7163-007 3
R13,R16 100 ohms 7163-027 2
R14 120 ohms 7163-029 1
R15 680 ohms 7163-047 1
R18,R22,R23 1K 7163-051 3
R17 4.7k 7163-067 1
R3 10k 7163-075 1
R7,R8,R10,R11 22k 7163-083 4
R4 47k 7163-091 1
R19, R21 100k 7163-099 2
R20* 150k* optional, sets the start level for inverted output (see text) 7163-103 1
R6, R12 1M 7163-122 1
R5 1.2M 7163-128 1
P1,P2,P3 1M log 7300-070 3
P4 10k lin 7300-230 1
C3,C5 10n polyester film 7212-713 2
C6,C7 100nF ceramic or polyester film 7212-749 3
C4a 1µF 35V tantalum 7213-210 1
C4b 10µF 35V tantalum 7213-212 1
C1,C2 22µF 35V polarised 7213-113 2
LD1 Panel Mount 7213-900 1
LD1 LED, red low current 7213-901 1
JK1,JK2,JK3 female jack socket 7212-203 3
SW1 push button (push to make) 7212-253 1

R17 : sets the range of the inverted output, if you use a 150K for R17 the inverted output will start from 10V (quiet state) to 0V (full range). If you don't install R17 (leave its place empty) then the range will be 0V (quiet state) to -10V (full range).

No FAQ found

Another high-quality PCB and kit from Yusynth/Soundtronics - well laid out and labelled, this one with no trimming or calibration needed. This was a straightforward and enjoyable project for me, a semi-beginner in circuitry. My only addition to the kit supplied was a very tiny momentary switch for the manual trigger; this meant that with homemade brackets I could fit the works behind an 8hp 3U panel. (Yusynth boards will fit fine in 3U Euro space, but be aware that some are quite deep so judicious placement may be in order, like, not stuffed against the power supply.) My Yusynth ADSR now resides beside its Doepfer counterpart, equally excellent and half the cost - plus I gained knowledge through building it myself. Follow the instructions and it'll work as advertised on completion. I'm really happy with it - now on to the next Soundtronics build!
Write a review

Customers also bought ....

7220-910
£1.50 (£1.80 UK, incl VAT)
7220-910
Our 3mm thick acrylic size 4 PCB holders are for use with the following YuSynth PCBs: YuSynth VCA YuSynth ADSR YuSynth S&H YuSynth Audio...
Out of stock

7212-206
£14.28 (£17.14 UK, incl VAT)
7212-206
A pack of 6 high quality 1/4" mono jack sockets that we use as standard on our MFOS range of synth modules. These sockets are the PCB...
In stock

7220-901
£1.50 (£1.80 UK, incl VAT)
7220-901
Our 3mm thick acrylic size 1 PCB holders are for use with the following YuSynth PCBs: YuSynth VCO LM394 YuSynth Steiner VCF YuSynth ARP VCF...
Out of stock
Please allow 5-7 days for shipping

7212-203
£7.14 (£8.57 UK, incl VAT)
7212-203
A pack of 3 high quality 1/4" mono jack sockets that we use as standard on our MFOS range of synth modules. These sockets are the PCB...
In stock

7212-106
£6.43 (£7.72 UK, incl VAT)
7212-106
A pack of 6, black aluminium-clad plastic knob with an attractive professional finish. The black anodised body is relieved by bright, diamond-cut features...
In stock